EV2365DN-00A【PDF 8/11 页】3A, 28V, 1.4MHz Step-Down Converter

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录362799

4页 5页 6页 7页 [8页]9页 10页 11页

MP2365 – 3A, 28V, 1.4MHz STEP-DOWN CONVERTER

MP2365 Rev. 0.91

7/10/2006

www.MonolithicPower.com

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.

Compensation Components

MP2365 employs current mode control for easy

compensation and fast transient response. The

system stability and transient response are

controlled through the COMP pin. COMP pin is

the output of the internal transconductance

error amplifier. A series capacitor-resistor

combination sets a pole-zero combination to

control the characteristics of the control system.

The DC gain of the voltage feedback loop is

given by:

OUT

VEA

LOAD

VDC

Where A

VEA

is the error amplifier voltage gain, G

is the current sense transconductance and R

LOAD

is the load resistor value.

The system has two poles of importance. One is

due to the compensation capacitor (C3) and the

output resistor of error amplifier, and the other is

due to the output capacitor and the load resistor.

These poles are located at:

VEA

LOAD

Where

transconductance, 530μA/V.

the

error

amplifier

The system has one zero of importance, due to

the compensation capacitor (C3) and the

compensation resistor (R3). This zero is located

at:

The system may have another zero of

importance, if the output capacitor has a large

capacitance and/or a high ESR value. The zero,

due to the ESR and capacitance of the output

capacitor, is located at:

ESR

In this case, a third pole set by the compensation

capacitor (C6) and the compensation resistor

(R3) is used to compensate the effect of the ESR

zero on the loop gain. This pole is located at:

The goal of compensation design is to shape

the converter transfer function to get a desired

loop gain. The system crossover frequency

where the feedback loop has the unity gain is

important.

Lower crossover frequencies result in slower

line and load transient responses, while higher

crossover frequencies could cause system

unstable. A good rule of thumb is to set the

crossover frequency to approximately one-tenth

of the switching frequency or lower. The

switching frequency for the MP2365 is 1.4MHz,

so the desired crossover frequency is equal to

or less than 140KHz.

Table 3 lists the typical values of compensation

components for some standard output voltages

with various output capacitors and inductors.

The values of the compensation components

have

been

optimized

responses

and

good

conditions.

Table 3—Compensation Values for Typical

Output Voltage/Capacitor Combinations

for

stability

fast

transient

given

OUT

(V)

1.8

2.5

3.3

L (μH)

C2 (μF,

Ceramic)

2 x 22

)

7.5

44.2

(nF)

3.3

4.7

5.6

4.7

2.2

None

2.2 - 4.7

4.7 – 6.8

6.8 - 10

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式